Eurotek Rules

Edge hardened rotary cutting rule with a round teeth configuration, requiring less pressure than other rules, allowing faster machine speed and increasing life time of the anvils blankets. Universal use for thin up to heavy corrugated boards. Available in 8; 10 and 12 tpi.

cb

Specifications »
 
X

Specifications for Eurotek Rules

Standard dimensions for rules for rotary dies

bevelsside and centre bevel/ toothings for all applications
hardnessH2; H2 TopDurFlex
Standardstästandard thickness1.42 mm
standard heights23.8 - 26.4 mm

Standard dimensions for especially low or high rules

bevelsside and centre bevel/ toothings for all applications
hardnessH2; H2 TopDurFlex
special thickness1.05; 2.0 mm
special heights20.0 - 23.7 mm & 26.5 - 80.0 mm
to top
Serrated Rules

Basic rule for all rotary die cutting applications. Available in 8; 10; 12; 16 and 20 tpi in side and centre serration

sb

cb

Specifications »
 
X

Specifications for Serrated Rules

Standard dimensions for rules for rotary dies

bevelsside and centre bevel/ toothings for all applications
hardnessH2; H2 TopDurFlex
Standardstästandard thickness1.42 mm
standard heights23.8 - 26.4 mm

Standard dimensions for especially low or high rules

bevelsside and centre bevel/ toothings for all applications
hardnessH2; H2 TopDurFlex
special thickness1.05; 2.0 mm
special heights20.0 - 23.7 mm & 26.5 - 80.0 mm
to top
Rotary Cutting Rules

Due to its very sharp bevel, this solid rule penetrates material easily, and is especially recommended for thicker corrugated board grades.

cb

Specifications »
 
X

Specifications for Rotary Cutting Rules

Standard dimensions for rules for rotary dies

bevelsside and centre bevel/ toothings for all applications
hardnessH2; H2 TopDurFlex
Standardstästandard thickness1.42 mm
standard heights23.8 - 26.4 mm

Standard dimensions for especially low or high rules

bevelsside and centre bevel/ toothings for all applications
hardnessH2; H2 TopDurFlex
special thickness1.05; 2.0 mm
special heights20.0 - 23.7 mm & 26.5 - 80.0 mm
to top
Multicut Rules

To round up Rotary Cutting Rules, this product enables alternative applications. It is equipped with lateral ground teeth and centred bevel. The diecutting result is a slight wave and it can be used as a Safety Edge Rule, in order to avoid cuts in the fingers.

sb, centered

Specifications »
 
X

Specifications for Multicut Rules

Standard dimensions for rules for rotary dies

bevelsside and centre bevel/ toothings for all applications
hardnessH2; H2 TopDurFlex
Standardstästandard thickness1.42 mm
standard heights23.8 - 26.4 mm

Standard dimensions for especially low or high rules

bevelsside and centre bevel/ toothings for all applications
hardnessH2; H2 TopDurFlex
special thickness1.05; 2.0 mm
special heights20.0 - 23.7 mm & 26.5 - 80.0 mm
to top
Kleancut Rules

Rule developed to minimize liner burst on corrugated board. At the same time the particular tooth shape provides excellent stripping results. Standard: side serration.

sb, centered

Specifications »
 
X

Specifications for Kleancut Rules

Standard dimensions for rules for rotary dies

bevelsside and centre bevel/ toothings for all applications
hardnessH2; H2 TopDurFlex
Standardstästandard thickness1.42 mm
standard heights23.8 - 26.4 mm

Standard dimensions for especially low or high rules

bevelsside and centre bevel/ toothings for all applications
hardnessH2; H2 TopDurFlex
special thickness1.05; 2.0 mm
special heights20.0 - 23.7 mm & 26.5 - 80.0 mm
to top
Pointed Cut Rules

This very aggressive edge hardened bevel shape penetrates corrugated boards easily. The comparatively long bevel with round gullet in the tooth and maximum sharpness requires slightly higher rule height than usual. It is recommended to set this rule with caution so as not to damage the teeth.

cb

Specifications »
 
X

Specifications for Pointed Cut Rules

Standard dimensions for rules for rotary dies

bevelsside and centre bevel/ toothings for all applications
hardnessH2; H2 TopDurFlex
Standardstästandard thickness1.42 mm
standard heights23.8 - 26.4 mm

Standard dimensions for especially low or high rules

bevelsside and centre bevel/ toothings for all applications
hardnessH2; H2 TopDurFlex
special thickness1.05; 2.0 mm
special heights20.0 - 23.7 mm & 26.5 - 80.0 mm
to top
Waved Cutting Rules

All standard wavings can be produced from the different rotary rules available. An unwritten rule: the finer the waves the finer the teeth. As long as there are no different indications, production will be made from Serrated Rules.

cb

Specifications »
 
X

Specifications for Waved Cutting Rules

Standard dimensions for rules for rotary dies

bevelsside and centre bevel/ toothings for all applications
hardnessH2; H2 TopDurFlex
Standardstästandard thickness1.42 mm
standard heights23.8 - 26.4 mm

Standard dimensions for especially low or high rules

bevelsside and centre bevel/ toothings for all applications
hardnessH2; H2 TopDurFlex
special thickness1.05; 2.0 mm
special heights20.0 - 23.7 mm & 26.5 - 80.0 mm
to top